Previous Thread
Next Thread
Print Thread
Fatal Error #112440
02/01/18 04:26 PM
02/01/18 04:26 PM
Joined: May 2013
Posts: 8
J
Jer Offline OP
Member
Jer  Offline OP
Member
J
Joined: May 2013
Posts: 8
I'm getting a fatal error with the latest QMC2 and Mame 0.194. Was not happening with Mame 0.193.
emulator #0 finished, exit code = 3 (fatal error), exit status = normal, remaining emulators = 0

Re: Fatal Error [Re: Jer] #112441
02/01/18 06:07 PM
02/01/18 06:07 PM
Joined: May 2008
Posts: 4,892
Germany
Q
qmc2 Offline
Very Senior Member
qmc2  Offline
Very Senior Member
Q
Joined: May 2008
Posts: 4,892
Germany
Works fine here on Linux at least. Which OS are you using?

Is there something printed to the emulator log?

Alternatively, does it work correctly from command line? See front-end log for the command used.


A mind is like a parachute. It doesn't work unless it's open. [Frank Zappa]

We're searching for QMC2 translators and support for existing translations. Interested? See here!
Re: Fatal Error [Re: Jer] #112442
02/01/18 06:43 PM
02/01/18 06:43 PM
Joined: Jun 2017
Posts: 20
USA
MusicLovr Offline
Member
MusicLovr  Offline
Member
Joined: Jun 2017
Posts: 20
USA
Don't see any problem, here (Win10 x32 & x64)...

Re: Fatal Error [Re: Jer] #112447
02/01/18 10:02 PM
02/01/18 10:02 PM
Joined: May 2013
Posts: 8
J
Jer Offline OP
Member
Jer  Offline OP
Member
J
Joined: May 2013
Posts: 8
Emulator Log shows this stderr[#0]: Fatal error: Could not load controller file xarcade.cfg

I'll have to go through and see where I went wrong with the controller setting. Thanks.

Re: Fatal Error [Re: Jer] #112448
02/01/18 10:13 PM
02/01/18 10:13 PM
Joined: May 2013
Posts: 8
J
Jer Offline OP
Member
Jer  Offline OP
Member
J
Joined: May 2013
Posts: 8
I can't figure out why I get the above error. Working directory is set to Mame. The xarcade.cfg file is in the ctrlr folder withiin mame like it always is. Any ideas?
Win10 X64

Last edited by Jer; 02/01/18 10:13 PM.
Re: Fatal Error [Re: Jer] #112457
02/02/18 08:46 AM
02/02/18 08:46 AM
Joined: May 2008
Posts: 4,892
Germany
Q
qmc2 Offline
Very Senior Member
qmc2  Offline
Very Senior Member
Q
Joined: May 2008
Posts: 4,892
Germany
I have no idea. If all you did is replace MAME 0.193 with MAME 0.194 (official Windows builds) it must be related to some changes in the last MAME version... probably a MAME-dev can shed some light on it?


A mind is like a parachute. It doesn't work unless it's open. [Frank Zappa]

We're searching for QMC2 translators and support for existing translations. Interested? See here!
Re: Fatal Error [Re: Jer] #112467
02/03/18 01:32 AM
02/03/18 01:32 AM
Joined: May 2013
Posts: 8
J
Jer Offline OP
Member
Jer  Offline OP
Member
J
Joined: May 2013
Posts: 8
I re-installed and it's working again. Thanks.

One other question - If I set the Machine List view to 'Hierarchical View' is it normal behavior for QMC2 to revert back to 'Full Detail View' upon exiting program and starting back up? Hierarchical View setting doesn't stick.

Re: Fatal Error [Re: Jer] #112468
02/03/18 02:06 AM
02/03/18 02:06 AM
Joined: Jun 2017
Posts: 20
USA
MusicLovr Offline
Member
MusicLovr  Offline
Member
Joined: Jun 2017
Posts: 20
USA
Fixed in rev. 8238 - so should be good, at next release:

Revision: 8238
Author: renereucher
Date: Sunday, December 03, 2017 4:21:49 AM
Message: fix: corrected the restoration of the last machine list view during initialization for non-WIP builds

Re: Fatal Error [Re: Jer] #112471
02/03/18 09:21 AM
02/03/18 09:21 AM
Joined: May 2008
Posts: 4,892
Germany
Q
qmc2 Offline
Very Senior Member
qmc2  Offline
Very Senior Member
Q
Joined: May 2008
Posts: 4,892
Germany
See here for an intermediate build which contains this and other fixes.


A mind is like a parachute. It doesn't work unless it's open. [Frank Zappa]

We're searching for QMC2 translators and support for existing translations. Interested? See here!
Re: Fatal Error [Re: Jer] #112480
02/03/18 09:29 PM
02/03/18 09:29 PM
Joined: Jun 2017
Posts: 20
USA
MusicLovr Offline
Member
MusicLovr  Offline
Member
Joined: Jun 2017
Posts: 20
USA
Hey, thanks! Works fine smile


Moderated by  qmc2 

Who's Online Now
3 registered members (dxl, natocccp, Vas Crabb), 27 guests, and 3 spiders.
Key: Admin, Global Mod, Mod
Shout Box
Forum Statistics
Forums9
Topics8,600
Posts112,408
Members4,821
Most Online283
Oct 11th, 2018
Powered by UBB.threads™ PHP Forum Software 7.6.1.1
(Release build 20180111)
Page Time: 0.275s Queries: 14 (0.254s) Memory: 5.6609 MB (Peak: 5.8819 MB) Zlib enabled. Server Time: 2018-11-21 12:21:37 UTC